Fundamentals of Vehicle Dynamic by Thomas Gillespie PDF free download

Thomas Gillespie Fundamentals of Vehicle Dynamic PDF, was published in 1992 and uploaded for 500-level Engineering students of Federal University of Technology, Owerri (FUTO), offering ATE503 course. This ebook can be downloaded for FREE online on this page.

Fundamentals of Vehicle Dynamic ebook can be used to learn Vehicle Dynamic, Dynamic Axle Loads, acceleration performance, power-limited acceleration, power train, automatic transmissions, braking forces, brakes, tire-road factor, Brake Proportioning, Anti-Lock Brake Systems, braking efficiency, rear wheel lockup, pedal force gain, road loads, aerodynamics, aerodynamic forces, Aerodynamics Aids, Rolling Resistance, Vehicle Response Properties, Low-Speed Turning, steady-state cornering, suspension, Anti-Pitch Suspension Geometry, MacPherson Strut, Roll Center Analysis, Solid Axle Roll Centers, Independent Suspension Roll Centers, active suspensions, steering system, Steering Geometry Error, Steering System Forces, Steering System Models, Four-Wheel Steer, rollover, tires, Tire Construction, Camber Thrust, Combined Braking, Cornering, Durability Forces.

Technical Details
Updated at:
Size: 5.29 MB
Number of points needed for download: 47
Number of downloads: 97

Books related to Fundamentals of Vehicle Dynamic

Fundamentals of Automotive and Engine Technology Standard Drives, Hybrid Drives, Brakes, Safety Systems

Author: Konrad Reif

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: ATE403

Topics: History of the automobile, History of the diesel engine, Areas of use for diesel engines, Basic principles of the diesel engine, Basic principles of diesel fuel injection, Basics of the gasoline (SI) engine, Inductive ignition system, Transmissions for Motor Vehicles, Motor-vehicle safety, Basic principles of vehicle dynamics, car braking systems, Vehicle electrical systems, electrical and electronic systems, Control of gasoline engines, Control of Diesel engines, Lighting technology, Electronic stability program, Adaptive cruise control, Occupant-protection systems, Hybrid drives, Operation of hybrid vehicles, Regenerative braking system, Workshop technology

Traffic Road safety and Equipment

Author: Niyi Adegoke, Vide Adedayo

School: National Open University of Nigeria

Department: Administration, Social and Management science

Course Code: CSS443

Topics: Road safety, Road Safety Issues, Road Safety Principles, Road Safety Strategies, Road Safety Signs, Road Safety Audit, Traffic Control, Federal Road Safety Commission, Traffic Management Unit, Road Functions, Operational Equipment, Intelligent Transportation System, Intelligent Transportation Application, Road Accident, Road Accident Analysis, Urban Traffic Management, Urban Traffic Problems, Solving Urban Traffic Problems, Rural Accessibility, Solving Road Transport Problems, Drivers Attitudes, Drivers Behaviour, Road Management

Power Systems Analysis ,3rd edition

Author: Hadi Saadat

School: University of Ibadan

Department: Engineering

Course Code: EEE511

Topics: Power Systems Analysis, power system, electric power generation, fossil power plants, hydroelectric power plants, solar power, wind power plants, geothermal power, biomass power plants, fuel cell, modern power system, smart grid, energy control center, complex power, complex power balance, power factor corrrection, per phase analysis, balanced three-phase power, generator models, transformer models, per unit system, transformer performance, autotransformers, three-winding transformers, transmission line parameters, line model, line compensation, power flow analysis, bus admittance matric, Gauss-Seidel power flow solution, Newton-Raphson method, power flow programs, synchronous machine, transient analysis, unbalanced fault, stability, swing equation, transoent stability, steady-state stability, power system control, automatic generation control, load frequency control, MATLAB, frequency response, reactive power, voltage control, excitation system

Applied mechanics, 3rd edition

Author: Hannah, MJ Hillier

School: Federal University, Oye-Ekiti

Department: Engineering

Course Code: MEE203

Topics: Applied mechanics, statics, mass, force, weight, couple, frameworks, friction, square-threaded screw, tribology, average speed, constant speed, velocity, free falling bodies, inertia, Variable forces, Periodic Motion, Simple harmonic motion, Car wheel balancing, Periodic time, simple pendulum, resonance, Angular acceleration, Centripetal acceleration, Centripetal force, Centrifugal force, Dynamic instability, balancing, static balance, dynamic balance, springs, energy, kinetic energy, potential energy, impulse, momentum, Impulsive forces, Inelastic collisions, aircraft, rockets, Reaction propulsion, Jet propulsion aircraft, Helicopters, Rocket propulsion, thrust, Ductile metals, metal, alloy, Shear Force, Bending Moment, Bending moment diagram, Poisson's ratio, stress, strain, Strain energy, Combined loading, Combined Bending, Direct Stress, fluid, pressure, Experimental Errors, discrepancy, error

Concrete Technology Theory and Practice, Multicolour Edition

Author: MS Shetty

School: Bayero University, Kano

Department: Engineering

Course Code: CIV5307

Topics: Concrete technology, Cements, Modern cements history, Portland cement manufacturing, Portland cement wet process manufacturing, Portland cement dry process manufacturing, Cement chemical composition, Cements hydration, Heat of hydration, Calcium silicate hydrates, Calcium hydroxide, calcium aluminate hydrates, hydrated cements structure, Water requirement for hydration, Cement types, ASTM cements classification, Ordinary Portland cement, Rapid hardened cement, Extra rapid hardening cement, Portland slag cement, Quick setting cement, super sulphated cement, low heat cement, Portland pozzolana cement, coloured cement, hydrophobic cement, masonry cement, expansive cement, Cement testing, Aggregates, aggregates testing, Aggregates form igneous rock, aggregates from sedimentary rocks, aggregates from metamorphic rock, aggregate crushing value, aggregates impact value, aggregate abrasion value, Deval attrition test, Dorry Abrasion test, Los Angeles test, modulus of elasticity, bulk density, specific gravity, Sieve analysis, Aggregates testing, Water, water qualities, Sea water for mixing concrete, Admixture, construction chemicals, Plasticizers, water reducers, Workability, Plasticizers action, Superplasticizers classification, Factors affecting workability, Superplasticizers types, Fresh concrete, Fresh concrete water content, Fresh concrete mix proportions, Aggregates sizes in fresh concrete, Aggregates shape, Surface texture, Admixture use in fresh concrete, Workability measurement, Slump test, k-slump test, aggregates grading, compacting factor test, flow test, flow table apparatus, vee bee consistometer test, setting of concrete, Manufacture of concrete process, Concrete compaction, Concrete curing, Concrete strength, Water-cement ratio, Strength gaining with age, Concrete maturity concept, Bond strength, High strength concrete, Elasticity, Creep, Shrinkage, Aggregates elastic properties, Modulus of Elasticity, Dynamic modulus of elasticity, Poison's ratio, Creep rheological representation, Creep measurement, Factors affecting creep, Aggregate influence, Mix proportion influence, Shrinkage, Plastic Shrinkage, Drying Shrinkage, Moisture movement, Autogenous Shrinkage, Carbonation shrinkage, Concrete Durability, Strength to Durability relationship, Concrete volume change, Durability definition, durability significance, Permeability, Cement paste permeability, Concrete permeability, Plastic shrinkage cracks, Settlement cracks, Thermal shrinkage, Hardened concrete testing, Concrete mix design, Special concrete, concrete methods

Control System Engineering, second edition

Author: Nagoor Kani

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: EEE307, MCE312

Topics: Mathematical model, time response analysis, time response, test signal, impulse response, order of a system, partial fraction expansion, Response of first order system, Response of second order system, time domain specification, steady state error, static error constant, error coefficient, automatic control system, controller, time response analysis, frequency response, sinusoidal transfer function, transfer function, frequency domain, frequency response plot, Bode plot, Magnitude plot, phase plot, Nichols plot, M-circle, N-circle, Nichols chart, Bounded input Bounded output stability, root locus, Routh Hurwitz criterion, Nquist plot, open loop system, closed loop system, mechanical translational system, Laplace transform, mechanical rotational system, electrical system, analogous circuit, block diagram, signal flow graph

Traffic Planning and Engineering ,2nd edition

Author: FD Hobbs

School: National Open University of Nigeria

Department: Administration, Social and Management science

Course Code: CSS342

Topics: Traffic Planning, Traffic Engineering, Traffic Studies, Traffic Surveys, Traffic Analysis, Transportation Surveys, Travel Surveys, Parking, Commercial Vehicle Survey, Public Transport SurveymTaxi Cab Survey, Travel Data, Transport Models, Trip Generation, Trip Rate Data Banks, Trip Distribution, Traffic Assignment, Parking Surveys, Street Parking, Off-street Parking, Traffic Management, Environmental Management, Public Transport, Freight Interchanges, Road User, Vehicle Warning, Road Alignment, Vehicle Performance, Traffic Stream, Traffic Capacity, Traffic Flow Relationships, Overtaking, Vehicle Movements, Vehicle Maneuvers, Traffic Control Systems, Cycle Time Choice, Vehicle Actuated Signals, Bus Signals, Coordinated Signal Systems, Area Traffic Control, Wide Area Control, Traffic Signal Equipment, Street Lighting, Traffic Signs, Carriageway Markings, Street Lighting Sources

An Instructor’s Solutions Manual to Accompany Engineering Mechanics statics, 4th edition

Author: Andrew Pytel, Jaan Kiusalaass

School: University of Benin

Department: Engineering

Course Code: MEE211

Topics: statics, Newtonian mechanics, force systems, force, couples, coplanar force systems, coplanar equilibrium analysis, equilibrium, Three-dimensional equilibrium, free-body diagrams, independent equilibrium equations, beams, cables, dry friction, ropes, flat belt, disk friction, rolling resistance, centroids, distributed loads, moments, Mohr's circle, virtual work, potential energy, virtual displacements

Engineering Mechanics, Statics 4th edition

Author: Andrew Pytel, Jaan Kiusalaass

School: University of Benin

Department: Engineering

Course Code: MEE211

Topics: statics, Newtonian mechanics, force systems, force, couples, coplanar force systems, coplanar equilibrium analysis, equilibrium, Three-dimensional equilibrium, free-body diagrams, independent equilibrium equations, beams, cables, dry friction, ropes, flat belt, disk friction, rolling resistance, centroids, distributed loads, moments, Mohr's circle, virtual work, potential energy, virtual displacements

Principle of Construction

Author: Nasiru Danlami

School: Bayero University, Kano

Department: Engineering

Course Code: CIV3301

Topics: Civil Engineering Procedure, civil engineering, Structural Engineering, Environmental Engineering, Water Resources Engineering, Hydraulic Engineering, Geotechnical Engineering, Construction Engineering, Civil Engineering Design, Applied Civil Engineering Design, Civil Engineering Design Documents, construction process management, site analysis, Site reconnaissance, surveys, measured survey, condition survey, Photographic survey, video surveys, Site Investigation, Foundation design, subsoil examination, trial pits, borehole, Window samplers, Rotary Drilling Equipment, Percussion boring, construction principles, construction equipment, earthing moving equipment, bulldozer, Frontend Loader, Motor Graders, scrapers, truck, Excavating Equipment, construction elements, Foundation construction, foundation types, Strip foundations, Wide strip foundation, Short-bored pile foundations, Pad foundations, Raft foundations

Power Systems. The electric power engineering handbook ,3rd edition

Author: Leonard Grigsby

School: University of Ibadan

Department: Engineering

Course Code: EEE511

Topics: power systems, Per-Unit System, Power System, power flow analysis, fault analysis, power system analysis, power system simulation, power system transients, lightning strokes, overvoltage, switching surges, very fast transients, Transmission System Transients, Grounding, Transient Recovery Voltage, Surge Arresters, Insulation Coordination, power system planning, Short-Term Load, Transmission Plan Evaluation, power system reliability, Electricity Pricing, Power Semiconductor Devices, uncontrolled rectifiers, controlled rectifiers, inverters, active filters, power electronics

Applied Thermodynamics, 2nd edition

Author: RK Rajput

School: Federal University of Agriculture, Abeokuta

Department: Engineering

Course Code: MCE309

Topics: Applied Thermodynamics, Thermodynamics, steam, Internal Latent Heat, entropy, steam generators, boilers, steam boiler, Fire Tube Boilers, Water Tube Boilers, High Pressure Boilers, boiler mountings, draught, chimney, evaporative capacity, boiler efficiency, steam power cycles, Carnot cycle, Rankine cycle, Modified Rankine cycle, Regenerative cycle, Reheat cycle, Binary vapour cycle, reciprocating steam engine, compound steam engines, Multi-Cylinder Engines, uniflow steam engine, steam nozzles, nozzle efficiency, steam injector, steam turbines, turbine efficiencies, reheating steam, steam turbine governing, steam turbine control, steam condensers, condensing plant, jet condensers, surface condensers, gas power cycles, air standard efficiency, dual combustion cycle, Atkinson cycle, Ericsson cycle, Brayton cycle, internal combustion engines, Four-Stroke Cycle Engines, Two-Stroke Cycle Engines, ignition system, fuel injection system, electronic fuel system, cooling system, lubrication systems, Performance Number, Combustion Chamber Design, octane number, Diesel Knock, cetane number, supercharging, dissociation, Engine Performance Curves, Wankel Rotary Combustion Engine, Stratified Charge Engines, Duel-Fuel Engines, air compressors, Reciprocating Compressors, volumetric efficiency, Multi-stage Compression, compressor performance, intercooler, Compressed Air Motors, Rotary Compressors, gas turbines, jet propulsion, Open Cycle Gas Turbines, Constant Volume Combustion Turbines, Gas Turbine Fuels, refrigeration, Air Refrigeration System, Simple Vapour Compression System, Vapour Absorption System, Refrigerants, Air-conditioning Systems, Air-conditioning, load estimation, Air Distribution

Modern Power Systems Analysis,Third edition

Author: DP Kothar, IJ Nagrath

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PSE413

Topics: Inductance of Transmission Lines, Resistance of Transmission Lines, Capacitance of Transmission Lines, Representation of Power System Components, Load Flow Studies, Optimal System Operation, Automatic Generation, Voltage Control, Symmetrical Fault Analysis, Symmetrical Components, Power System Security, Power System Stability, Compensation in Power Systems, Load Forecasting Technique, Voltage Stability

Power System Engineering Planning, Design, and Operation of Power Systems and Equipment ,2nd edition

Author: Juergen Schlabbach, Karl-Heinz Rofalski

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PSE513

Topics: Power System Engineering, Power System Engineering planning, Power System Engineering design, power system load, load forecast, Low-Voltage Systems, power system planning principles, power system planning criteria, loss evaluation, energy losses, power losses, power system topology, Busbar Arrangements, Double Busbar Arrangement, transformers, Thermal Permissible Loading, cable systems, Permissible Current, overload lines, Flexible AC Transmission Systems, Parallel Compensation of Lines, Serial Compensation of Lines, Phase-Shifting Equipment, HVDC-Transmission, Converter Stations, Breakers, Reactors, Electrodes, Load-Flow Calculation, Short-Circuit Current Calculation, faults, disturbances, Overcurrent Protection, Impedance Protection, Differential Protection of Lines, Ground-Fault Protection, Buchholz Protection, Overvoltages, Insulation Coordination, Slow-Front Overvoltages, Fast-Front Overvoltages, Neutral Earthing, Residual Current Compensation

Manufacturing Engineering And Technology, Seventh Edition

Author: Steven Schmid, Serope Kalpakjian

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: MCE304

Topics: structure of metals, mechanical behavior of metals, manufacturing properties of metals, metal alloys, heat treatment, ferrous metals, alloy, Nonferrous metals, alloys, polymers, ceramic, glass, graphite, diamond, nano materials, composite materials, metal-casting processes, metal-casting equipment, metal casting, metal-rolling, metal-forging, metal extrusion, drawing processes, sheet-metal forming processes, powder metal, superconductors, plastics, rapid-prototyping processes, machining, cutting-tool materials, cutting fluids, machining processes, machining centers, machine-tool structures, machining economics, abrasive finishing, finishing operations, micromanufacturing, microelectronics devices, solid-welding processes, brazing, soldering, adhesive-bonding, mechanical fastening, surface technology, engineering metrology, instrumentation, quality assurance, computer-integrated manufacturing, computer-aided manufacturing

Design of Structural Elements

Author: WMC McKenzie

School: Bayero University, Kano

Department: Engineering

Course Code: CIV3307

Topics: Structural elements design, Structural Analysis Techniques, Shear Force, Bending moment, Shear force diagram, Bending moment diagram, Deflection of Beams, Elastic Shear stress distribution, Elastic Bending stress distribution, Transformed sections, Moment distribution, Bending stiffness, Rotational Stiffness, Carry-over moment, Pinned End, Free Moments, Fixed bending moments, Distribution Factors, Design Philosophies, Permissible stress Design, Load Factor Design, Limit State Design, Design codes, Eurocodes, National Annex, Structural Loading, Dead loads, Imposed loads, Imposed roof loads, Floor load distribution, Load distribution, Structural Instability, Overall Stability, Robustness, Reinforced concrete Element's Design, Structural Steelwork Elements' Design, Structural Timber Elements' Design.

Engineering economics material

Author: ENG FUTO

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: ENG212

Topics: Engineering economy, engineering process, debt capital, equity, interest, interest formula, time value of money, cash flows over time, single payment compound amount factor, single-payment present-worth factor, equal-payment-series compound-amount factor, present-worth factor, functional notation, interest-formula relations, arithmetic gradient series factor, uniform-gradient-series factor, nominal interest rates, effective interest rates, capital-recovery factor

A Textbook of Fluid Mechanics and hydraulic machines, 9th edition

Author: RK bansal

School: Covenant University

Department: Engineering

Course Code: CVE332

Topics: Fluid Mechanics, hydraulic machines, viscosity, compressibility, bulk modulus, surface tension, capillarity, vapor pressure, cavitation, Pascal's law, manometers, Piezometer, differential manometer, isothermal process, buoyancy, flotation, meta-center, fluid flow, continuity equation, velocity, acceleration, velocity potential function, stream function, equipotential line, Vortex flow, ideal flow, potential flow, momentum equation, free liquid jets, orifices, mouthpieces, notches, weirs, viscous flow, turbulent flow, Reynolds experiment, dimensional homogeneity, model analysis, dimensionless numbers, Boundary layer flow, compressible flow, Mach number, Jet propulsion, hydraulic machines, turbines, Pelton wheel, Radial flow reaction turbines, Francis turbine, axial flow reaction turbine, Draft tube, specific speed, unit quantities, centrifugal pumps, cavitation, maximum suction lift, net positive suction head, reciprocating pumps, air vessels, fluid system, hydraulic press, hydraulic accumulator, hydraulic intensifier, hydraulic ram, hydraulic lift, hydraulic crane, hydraulic coupling, hydraulic torque converter, air lift pump, gear-wheel pump

Practical Electrical Engineering

Author: Sergey Makarov, Reinhold Ludwig, Stephen Bitar

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: ENG226, EEE301

Topics: DC Circuits, Operational Amplifier, Nonlinear Passive Circuit Elements, independent sources, dependent sources, time-varying sources, voltmeter, circuit law, network theorem, circuit analysis, power transfer, Operational Amplifier, Amplifier Models, Transient Circuit, Dynamic Circuit Elements, AC Circuits, Steady-State AC Circuit, filter circuit, bode plot, frequency response, Fourier transform, RLC circuit, AC Power, power distribution, transformer, inductor, digital circuit, switching circuit, analog-to-digital conversion, embedded computing, Diode, Transistor Circuits, Bipolar Junction Transistor, BJT Circuits, MOS Field-Effect Transistor, MOSFET

Theory of machines

Author: MEE302

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: MEE302

Topics: Kinematics, Kinetics of Mechanisms, Balancing of Machines, Rotating masses, Reciprocating masses, Cams, Followers, Flywheel, Gears, Gears trains, Friction Clutches, Belt drives, Band Brakes, Power Screw, Universal Joint, .Gyroscope, Speed Governors, Steering mechanism

Past Questions related to Fundamentals of Vehicle Dynamic

Farm power and maintenance

Year: 2017

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: FPE510

Topics: Farm power, farm maintenance, piston, brake power, tractor engine friction power, engine systems, fiel system, cooling system, lubrication system, electrical system, hydraulic system, API hydrometer, fuel specific gravity, traction, dynamic traction ratio, tractive efficiency, travel reduction slip

Maintenance of engineering systems

Year: 2020

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: MEE501

Topics: Engineering system maintenance, maintenance tools, maintenance schedules, refrigeration operation, air conditioning system operation, refrigerants, workshop maintenance timing, direct injection compression ignition engine, injector nozzle, compression ignition engine inlet valve, automobile steering system, comber angle, castor angle, Akerman angle, center point steering

Computer aided design and computer and computer aided manufacture

Year: 2020

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: MEE505

Topics: Computer aided design, computer aided manufacture, Isometric view drawing, CNC Codes, rapid traverse positioning, CNC turning, computer aided manufacturing operation, tool-holding magazine, machining centers, milling centers, surface finishing operation, Mathematical matrix notation, Bezier cubic curve, Hermite cubic curve, translation transformation, scaling transformation, rotation transformation, parametric modeling, parametric Bezier equations

Heat and power machinery

Year: 2020

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PME405

Topics: Heat machinery, power machinery, internal combustion engine, indicator diagram, indicated horsepower, brake horsepower, clearance volume, simple carburetor, ignition delay, fuel calorific value, mechanical efficiency, volumetric efficiency, indicated thermal efficiency

Electric power system and machines

Year: 2019

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PSE312

Topics: Electric power system, electric power machine, load fluid studies, load fluid studies method, Jacobian matrix, apparent power, real power, active power, lap winding, wave winding, frog leg winging, primary winding, secondary winding, generator types, dc generator

Weaving mechanism

Year: 2019

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PTE308

Topics: Weaving mechanism, maximum permissible loom speed, conventional automatic power loom, non conventional automatic power loom, plain weave, dubby shedding, target shedding

HEAVY CONSTRUCTION EQUIPMENT AND METHODS

Year: 2017

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: CIE503

Topics: rolling resistance, altitude, earth work, sheer hills, excavators, power crane

SPECIAL TOPICS IN POWER SYSTEM ENGRINEERING

Year: 2018

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PSE514

Topics: electricity market, power system operation, power system control systems, power system communication systems, solar installation, power lines

FLUID MECHANICS 2

Year: 2018

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: ENG310

Topics: fluid velocity, velocity potential, dimensional analysis, hydraulic power plant, pelton wheel, hydraulic, mach number, mach angle, gross head, net head, hydraulic efficiency, shock-wave, vortex, Fronde's number, Reynolds number

Mechanical engineering design test

Year: 2021

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: MCE301

Topics: shafts, combined bending, torsional moments, fluctuating loads

Partial automatic labouratory

Year: 2020

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: MCE513

Topics: Partial automatic laboratory, Programmable Logic Controller internal architecture, Programmable Logic Controller address bus, Programmable Logic Controller input processing, Programmable Logic Controller output processing, Programmable Logic Controller output channels, Programmable Logic Controller program scan, latching, latched circuits, reed switch, incremental shaft encoder, photoelectric transmissive switch, diaphragm pressure switch, field bus, OSI model, repeater, bridge, router, SCADA system, SCADA architecture, batch mixing system

Antenna design and measurement

Year: 2020

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: COE514

Topics: Antenna design, antenna measurement, Antenna radiation pattern, Fraunhofer region, Fresnel region, Antenna temperature, Antennal effective area, parabolic antenna construction, parabolic antenna action, Yagi antenna, monopole, Antenna gain comparison technique, E-plane antenna, base transceiver station, mobile switching center

Power system engineering studio 1

Year: 2020

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PSE413

Topics: Power system engineering studio, Kirchhoff's current law, self admittance, transfer admittance, electrical faults, symmetrical faults, reactors, short circuit current, conductor flux, skin effect, proximity effect, line resistance, insulating materials, distribution transformer tap changer, lightening arresters, distribution station, insulation oil, electrical power angle, swing equation, power system stability, transmission line studies

Electrical drive system

Year: 2019

School: Federal University of Technology, Owerri

Department: Engineering

Course Code: PSE506

Topics: Electrical drive system, modern electric drive system, mechanical power developed, shaft speed, shaft torque, slip speed, line circuit, motor speed, efficiency, mechanical power, air gap power, stray power

Tests related to Fundamentals of Vehicle Dynamic

Physics (JAMB)

School: WAEC, JAMB & POST UTME

Department:

Course Code: JAMB

Topics: Physics, JAMB, Friction, work, force, motion, speed, velocity, energy, hydraulic press, relative density, hydrometer, gas law, sound wave, wave, light, mirror,capacitor, electricity, pressure

Biology (JAMB)

School: WAEC, JAMB & POST UTME

Department:

Course Code: JAMB

Topics: JAMB, UTME, biology, Plant cell, fern, plant biology, nutrition, circulatory system, osmoregulation, ecology, variation, hereditary, gene, chromosome, evolution

Mathematics (JAMB)

School: WAEC, JAMB & POST UTME

Department:

Course Code: JAMB

Topics: Mathematics, JAMB, Logarithm, standard form, permutation, combination, number system, set, ratio, indices, factorization, inequality